Search:

Type: Posts; User: akwrencher; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    98
    Views
    13,251

    Re: New Stand Alone Electronic Ignition System

    checked out your updated site. Very nice.
  2. Replies
    12
    Views
    344

    Re: Marking steel fittings.

    What about a label maker? They are only about 20 to 30 bucks. Useful for all sorts of things.
  3. Replies
    58
    Views
    4,040

    Re: Oil injection fuel pump

    Sorry for the necro post but after 4 pages and no mention of this I thought I would throw it out there for anyone interested in this sort of thing. A pump about like the OP describes dies exist. It's...
  4. Replies
    32
    Views
    430

    Re: Welding Aluminum any Pro's on here?

    I weld repaired a lower unit on a Honda 90 outboard several years ago, I think I used 4043 wire. Worked ok, fixed the broken skeg and filled in some really bad corrosion pitting, after grinding them...
  5. Replies
    11
    Views
    313

    Re: Suzuki 1.0-liter ignition

    http://www.homebuiltairplanes.com/forums/showthread.php?t=21617&page=7&p=460254#post460254
  6. Replies
    19
    Views
    470

    Re: Old HKS engines?

    Different critters. HKS is a four stroke, four strokes can still suffer corrosion if stored in a damp location and not pickled, but are much less susceptible, in general, to timing out due to...
  7. Replies
    20
    Views
    288

    Re: Welding 7075

    So, when I posted this I didn't exactly envision welding up entire airframes and such out of 7075 suddenly. I just stumbled upon it and thought it was neat that it was now possible. There are always...
  8. Replies
    20
    Views
    288

    Welding 7075

    Was surfing and found this. Might be interesting for someone.

    https://www.google.com/amp/s/phys.org/news/2019-01-nanotechnology-enables-weld-previously-un-weldable.amp
  9. Re: Another "bottom of the hour news report": Boeing flying car

    Not true, air taxi operator was what the Bush pilots became. Officially.
  10. Replies
    127
    Views
    1,897

    Re: Forum made EFI?

    Or these.....
    http://www.ecotrons.com
  11. Re: Firsthand experience or objective data on industrial V-twins for aircraft use?

    Spot on, except I'm not sure a wankel qualifies as a 4 stroke....
  12. Re: Firsthand experience or objective data on industrial V-twins for aircraft use?

    "Fuel cooling" is one reason, but a big one is that they are designed from the start to run 2 to 3 times as many rpms as the 4 strokes we are competing them too. More rpm means more fuel burned per...
  13. Re: Firsthand experience or objective data on industrial V-twins for aircraft use?

    http://https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F380856467103

    Bought this for a quad I'm working on. Was the most expensive ofbthebones I found, has a...
  14. Replies
    51
    Views
    669

    Re: Tuning a Zenith 14992 Carb on a 1/2 VW

    Before tuning a carb, you need to know if you have any vacuum leaks, timing is good, etc, and that the carb is clean and in good condition. Forgive me if you are already there, but you made no...
  15. Replies
    49
    Views
    1,461

    Re: composite ribs

    You will want to be very careful mixing aluminum and steel, they like to eat each other.......
  16. Re: "Micromaster"-- Centerline twin using small industrial engines

    You can use Heat fuel addative, it's some kind of alcohol. A pint bottle only soaks up a few teaspoons of water though, so if there is A lot, drain the fuel and carb, then fresh fuel and a little...
  17. Replies
    163
    Views
    2,543

    Re: Airplane Guy Needs Education: 103 Viability

    My boss has a Harley. I can't ride it more than 15 minutes without losing feeling in my hands. Vibration. It runs great though, and is anything but slow......
  18. Thread: Ebay Today

    by akwrencher
    Replies
    1,770
    Views
    149,494

    Re: Ebay Today

    http://https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F183554467554
  19. Replies
    143
    Views
    3,221

    Re: Best value used EXPERIMENTAL

    Scrapper, I don't have much advice for you, and don't know you well enough to expect you take it anyway, but I will offer some encouragement. It sounds to me like you need to make some changes, have...
  20. Replies
    28
    Views
    745

    Re: Biplane Forum

    It would be cool if everyone could view, but you pay to get rid of the ads. I will almost always pay for an app to be ad free if given a choice.
  21. Replies
    143
    Views
    3,221

    Re: Best value used EXPERIMENTAL

    Glad to hear from you. I just turbed 40 and seem to be getting grumpier with each passing year. Definitely a work in progress fixing that. Some serious attitude readjusting is my current struggle....
  22. Re: Some Alternative Ultralight Single Cylinder Engines!

    Many 4 stroke engines use a compression release. Many are even automatic, you don't even know they are there.
  23. Replies
    41
    Views
    2,515

    Re: Part 103 and electric flight

    Cool project, but wow, you weren't kidding, that was rugged.
  24. Thread: Ebay Today

    by akwrencher
    Replies
    1,770
    Views
    149,494

    Re: Ebay Today

    http://https://www.ebay.com/itm/VERY-NICE-ROTAX-447-WITH-DUAL-CARB-B-GEARBOX-MUFFLER-AND-ALL-ACESSORIES/273559761263?hash=item3fb16eb16f:g:4voAAOSwd49b1Bo0
    ...
  25. Replies
    57
    Views
    854

    Re: Prop makers?

    Anyone have a link to the Eiffel club props? I'm getting no where with google.....:ermm:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4