Quantcast

Recent content by wakataka

HomeBuiltAirplanes.com

Help Support HomeBuiltAirplanes.com:

  1. W

    Kawasaki 440A air cooled engine

    If it's a 440A (most common one used on aircraft), the full gasket set is Winderosa Part Number 711048. The top end set is 710048. I usually buy them from Manufacturers Supply mfgsupply.com
  2. W

    Rotax 503 Redrive Cog Removal

    Heat is your friend when pulling things off the tapered shaft. Heat expands the gear or pulley so it releases it's grip on the shaft. Be prepared for it to pop off with a bang and don't stand in front of it. A pneumatic impact wrench really helps getting the bolt off. I think the Rotax manual...
  3. W

    Kawasaki 440a missing issue.

    Have you tried running it with the kill switch disconnected to eliminate the possibility of a partial short in the ignition switch? You'd need to work out a way to shut it off, which can be dangerous with a spinning prop nearby. I once had an ignition switch go bad and the first sign was an...
  4. W

    85 lbs thrust from 14hp

    The Wright Flyer generated 90 pounds of thrust from 12 hp. The key to low-speed efficiency is big props (over 8 feet in diameter on the Flyer) turning slowly. To be efficient, ducted fans need fairly tight clearances between the duct and the blade tips. Maintaining those tight clearances on a...
  5. W

    Running 100LL in your 2 Stroke Full Time?

    I once ran a free-air Rotax 277 on it for about 30 hours with no problems. It was the only way I could keep the temps in range on that engine. I did notice the yellow color on the piston crown after running 100 LL. I now only run it occasionally when I have to fill up at an airport to get back...
  6. W

    Low wing Skypup

    The Sky Pup is indeed a well designed airplane and it flies just fine without ailerons. I flew with Steve Wood back in the early 1980's when he and his partners originally designed and flew the prototype, originally dubbed the "Blue Light Special" because it was made from blue foam. I recall...
  7. W

    Descending with a 2 stroke powered trike.

    If you watch the EGT, you can see it increase at a partial power descent. Different engine / prop combinations have different critical throttle ranges, but all of them I've ever seen are just fine descending at idle, because as you mention, the idle mixture is set very rich. There might be a...
  8. W

    Chotia Gypsy

    The Gypsy was made of aluminum rather than wood and it had ailerons. A friend of mine built and flew one back in the 80's. He used a Rotax 277 instead of the Chotia and it flew remarkably well. I always liked the looks of it.
  9. W

    Wanted Two Weedhopper (B?) Propellers for Two Chotia 460 engines

    The Chotia engine was a work in progress. I flew one for over 50 hours and it was about as reliable as the chain-saw and go-kart engines that were the norm back in the early days. That's not saying much. Off-field landings were to be expected. The climb rate on the Chotia powered Weedhopper was...
  10. W

    Wanted Two Weedhopper (B?) Propellers for Two Chotia 460 engines

    Weedhopper prop diameter is somewhat limited by ground clearance but also by prop tip speed. I don't recall what the RPM of the engine was but it is a direct drive, so the prop turns a lot faster than on reduction drive engines. When the prop tips approach 85% of the speed of sound, the prop...
  11. W

    What brand of Belt Drive is this?

    Might be an old Hegar. They made cog belt drives back in the 80's as I recall, although I don't recall I ever saw one on a 277. Here's some info that you might find relevant / interesting http://www.rotaryforum.com/forum/showthread.php?p=371760 One thing to be mindful of. Most (maybe all?) 277...
  12. W

    Rotax 447 rough idle

    One caution about compression test. If you've got electronic ignition, it's a good idea to ground the plug leads during compression test as damage can occur to the ignition system if it fires without a ground. You can just keep the ignition switch in the off position and it should be OK but I...
  13. W

    Reliability of Rotax 2-strokes

    Rotax seals are made of some kind of material that goes bad with age, not hours of use. There are more modern materials, like viton, that will last for decades but these aren't what you get when you order the standard parts from aircraft or snowmobile suppliers. The center crank seal is a...
  14. W

    New engine and carb. Proving not very reliable.

    There are two different stators for Kawasaki engines that are only about 0.010 difference in diameter. I've never learned how to tell the difference between them except that the 'big' stator won't fit in a 'small' flywheel. It will bolt up to the engine just fine, and you can even get the...
  15. W

    Ully floats

    I don't know what type of plastic it is, but if it's HDPE (like many kayaks are made of) it can be repaired by 'welding' with heat and HDPE rod or sheet. http://www.harborfreight.com/plastic-welding-kit-with-adjustable-temperature-96464.html
Top