Recent content by TreeTopPilot

HomeBuiltAirplanes.com

Help Support HomeBuiltAirplanes.com:

  1. T

    Tig Setup you use

  2. T

    Sky Raider/Ridge Runner plans /kits??

    great design...poor craftsmanship in making a...cough...kit Two of the spars I seen were welded....too many issues to even start with what we seen
  3. T

    If anyone has any Ridge runner kits...contact me . I can save you a lot of issues that I have...

    If anyone has any Ridge runner kits...contact me . I can save you a lot of issues that I have had to rebuild most everything that was given me. What a joke RRW are....sure probably not like this back in the day....but one has to wonder. You will have to make all the metal fittings as most were...
  4. T

    Sticker shock!

    Dillsburg--charly voglesong---did sell China origin tube later on near the end of the business. Only reason I know is because they didn't offer certs for the last 6 or 7 years they sold tube....just purchased from Spruce from then on. Plymouth or German tubing....less voids to be concerned with...
  5. T

    Ridge Runner 1?

    I hope this gets resolved for you. I am also bound by my lawyer by what I can state. There is a dark cloud building around this......
  6. T

    be aware:

    From the last shipment that was reported to be of Chinese origin with no certs available..........
  7. T

    TIG or gas welding...

    Some of my unfinished rudder and brake pedal units.... .375" and .500" x .035" wall molly. Weld should have some colors to them with no grey burnt areas at all. Machine set to 100 amps..... use your foot pedal !!!!!!
  8. T

    TIG Filler for 4130…

    Learn to use the foot pedal control for amperage. ER70S-2 for molly. Take your time and weld slow........and lots of practice.
  9. T

    Engineering question - Heat and 6061 T-6

    I have a set of wings based on a tubular aluminum spar....old Avid wings. The issue is that a propane torch was used by the previous owner to un-glue a gusset near the spar attach fitting. I didn't think of it until after the purchase was made. After some thought and research about the situation...
  10. T

    For Sale Rotax 503 SCDI for sale

    I baught this engine from Rotax Rick with less than 100 Hrs , 0 SMOH now , never taken off crate from receiving it after rebuild. Kept it inside my home and was turned every week. Has "C" gearbox with 3.00 gearset. Delivered with new Ducati set up, wires , boots, pistons, bearings and seals -...
  11. T

    So, you really want a Tig welder.......Here are the things I considered before buying

    Re: So, you really want a Tig welder.......Here are the things I considered before bu This is the stuff I work on building......
  12. T

    So, you really want a Tig welder.......Here are the things I considered before buying

    Re: So, you really want a Tig welder.......Here are the things I considered before bu You will be way ahead of the game with what I use.... Then after some yaers of using you will get welds like this I use a ThermalArc most at work, but the little Miller Maxstar STH is simply all I would...
  13. T

    LYC 4AO84 ??

    OK I have secured an engine. Now that some research has been done...I really think this is going to work out well. I plan to make a lighter oil pan assembly, replace the rotator retainers on the valve springs with titanium units, Tig up a nice , light stainless 4 into 1 exhaust, and replace some...
  14. T

    LYC 4AO84 ??

    OK...new here...just really wanting to see if anyone has been seccesful with these. I am looking at purchasing one with "0" hours....NIB manu date in 1999. Have plans to attach it to the front of a N3 Pup. I think this engine has a great sound and can be made quite...and if it will make 45HP...
Group Builder
Top