Recent content by Taiser

HomeBuiltAirplanes.com

Help Support HomeBuiltAirplanes.com:

  1. Taiser

    Yes and no... I'm happy I put them in, but the hassle to install, the issues I had with the...

    Yes and no... I'm happy I put them in, but the hassle to install, the issues I had with the flaperon adjustments (which I think these things caused) the extra weight and it makes getting in the plane a bit of a pain so if I had to do it again I wouldn't put them in, but now that they are in I'm...
  2. Taiser

    Zenith CH750 build...

    For comparison, here's my buddies plane parked in the lot next to mine after that mess of rain, snow and sleet we got!!! Wouldn't want that load off back of the wing sitting on my flaperon!!! :shock: Hope everyone has a safe and Merry Christmas and New Year!!! Mark
  3. Taiser

    Zenith CH750 build...

    Couple of shots of the "BB" in it's nest... nice and cozy! :)
  4. Taiser

    Zenith CH750 build...

    I used the "ratchet" method to put it on, only choice I had, but because it's so tight, it had to go at a weird angle (sorry no photo of the ratchet, just a large 1/2 drive one) and it took two of us to force it up. It basically chewed up the retaining tube!!! :( That tube is 4130 steel, so I...
  5. Taiser

    Zenith CH750 build...

    Inspected the nose gear channel too, nothing wrong with it. I thought for sure there would be something amiss in there with all the crap landings I did, but it's holding up fine. Seems I was worried for nothing. New bungee going in... this was NOT fun! :mad2:
  6. Taiser

    Zenith CH750 build...

    Had to take the nose gear off anyways to get the bungee in behind it so I took it right out for inspection. The nose gear always made me nervous. No issues though, even after some pretty "sporting" landings, trying to master the STOL. It held up well... Just some paint issues where the...
  7. Taiser

    Zenith CH750 build...

    :( Bungee tool won't fit on my setup, too much junk in the way, including the Mags, and the throttle linkage... Here's the tool... waste of money in my case, but I'll see if I can mod it somehow...
  8. Taiser

    Zenith CH750 build...

    Thought I would do a quick update! I managed to keep flying up until about a week ago!!! That was pretty sweet, but then it rained and it froze, then it snowed. What a mess!! :( Luckily I borrowed a buddies hangar until next year when I will build my own. I did manage to change out the...
  9. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    Finally found a use for the big-ass drawer in my new tool box! Perfect to keep my plans safe! :D
  10. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    Works pretty well! Another bulkhead. Lots of cutting to come!
  11. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    Double checking the template, you have to make sure you make the forms on the proper lines. Started to trace. Used a ruler where I could but most of it is free-hand. Needless to say, took a while and really sucks, but it's not something you want to rush.
  12. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    Tapped up the sheets big enough to cover the bulkhead patterns. Need something smooth tipped to trace with. Rear end of a small brush seems to fit the bill.
  13. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    This section of plans is about 8' long!!! It's a page designed to be cut out and used as templates... don't like that idea, so... Bought some carbon paper...
  14. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    Beam going together. Nice and straight. Done! Rock solid, kinda heavy and it's white to boot so will be easy to make marks on. I'll trim it once I start assembling the bulkheads.
  15. Taiser

    Taiser's Hummel H5 Build... Yes I'm at it again...!

    Starting off pretty simply. I bought a 4x8 foot sheet of 3/4" plywood for the forms. I also need to make a beam for the fuselage jig. I couldn't find anything to straight so I bought some particle board strips. Couldn't find any 12' so I wound up getting some 16' long ones. They will stay...
Top